Eurolite edx-4 pdf

Improper installation can result in bodily injury and or damage to property. The device has to be installed out of the reach of people. If the device shall be lowered from the ceiling or high joists, professional trussing systems have to be used. The device must never be fixed swinging freely in the room. Caution: Devices in hanging installations may cause severe injuries when crashing down! If you have doubts concerning the safety of a possible installation, do NOT install the device!

Mount the device to your trussing system using an appropriate clamp. For overhead use, always install a safety-rope that can hold at least 12 times the weight of the fixture. You must only use safety-ropes with quick link with screw cap.

Pull the safety-rope through the attachment eyelet on the device and over the trussing system or a safe fixation spot. Insert the end in the quick link and tighten the safety screw. The maximum drop distance must never exceed 20 cm. A safety rope which already hold the strain of a crash or which is defective must not be used again. Before taking into operation for the first time, the installation has to be approved by an expert!

The device must only be installed absolutely planar at a vibration-free, oscillation-free and fire-resistant location. Make sure that the device is installed absolutely planar by using a water-level. The device must be installed out of the reach of people. The device must always be installed via all fixation holes. Do only use appropriate screws and make sure that the screws are properly connected with the ground.

The durability of the installation depends very much on the material used at the installation area building material such as wood, concrete, gas concrete, brick etc. This is why the fixing material must be chosen to suit the wall material. Procedure: Step 1: On the baseplate, there are the holes for the installation.

Step 2: Hold the baseplate onto the location where the device is to be installed. Step 3: Mark the boreholes with a pen or a suitable tool. Step 4: Drill the holes. Step 5: Hold the baseplate in the desired position and tighten it. The occupation of the 8-pin DIN-socket is as follows: 1. Channel 1 2. Ground 3. Channel 4. If the device will be directly connected with the local power supply network, a disconnection switch with a minimum opening of 3 mm at every pole has to be included in the permanent electrical installation.

The device must only be connected with an electric installation carried out in compliance with the IECstandards. Connect your loads via the output-sockets. The maximum load per channel is 1, W resistive. Please note that the maximum current of 16 A must never be exceeded. Only use a stereo shielded cable and 3-pin XLR-plugs and connectors in order to connect the controller with the device or one device with another. Occupation of the XLR-connection:. Always connect one output with the input of the next device until all devices are connected.

Caution: At the last device, the DMX-cable has to be terminated with a terminator. To ensure that the control signals are properly directed to each device, the device requires adressing. This is to be done for every single device by changing the DIP switches as set out in this table.

The starting address is defined as the first channel from which the device will respond to the controller. If two, three or more device are addressed similarly, they will work similarly. This device can be defined as a 4-channel dimmer pack normal DMX or as with one address for all 4 channels DMX parallel.

Please adjust your selection via DIP-switch no. You can control the desired channel via you lighting controller. When a DMX-controller and an analog controller is connected, the device reacts to the stronger signal. The operator has to make sure that safety-relating and machine-technical installations are inspected by a skilled person once a year.

The following points have to be considered during the inspection: 1 All screws used for installing the devices or parts of the device have to be tighly connected and must not be corroded.

Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and any safety problems have to be removed. We recommend a frequent cleaning of the device. Please use a soft lint-free and moistened cloth. Never use alcohol or solvents! There are no servicable parts inside the device except for the fuse. Maintenance and service operations are only to be carried out by authorized dealers. Before replacing the fuse, unplug mains lead.

Procedure: Step 1: Open the fuseholder on the toppanel with a fitting screwdriver. Step 2: Remove the old fuse from the fuseholder. Step 3: Install the new fuse in the fuseholder. Step 4: Replace the fuseholder in the housing. Should you need any spare parts, please use genuine parts. If the power supply cable of this device becomes damaged, it has to be replaced by a special power supply cable available at your dealer. Should you have further questions, please contact your dealer.

Toujours connecter la fiche secteur en dernier. Des dysfonctionnements et court-circuits peuvent causer des blessures mortelles. Ceci annulerait toute garantie. La distance de chute maximale est 20 cm.

Pas 4: Forez les forures. Canal 1 2. Terre 3. Canal 4. Connectez vos consommateurs via les prises de sortie. Il se peut autrement que les appareil ne fonctionneront pas correctement. Occupation de la connection XLR:. Vous pouvez definer cet appareil comme dimmerpack 4 canaux normal DMX ou avec une adresse pour tous les 4 canaux DMX parallel.

Pour le nettoyage, utilisez un torchon non pelucheux humide. Pas 3: Installez le nouveau fusible au porte-fusible. Desembale su EDX Si los hubiese, consulte a su proveedor y no use el aparato. Please do not create new threads here, instead, use the categories above!

My first goal is to connect two lightbulbs to my computer and make sure I can dim them. I also tried to use some other fixtures for other 4 channel dimmers. Does anyone have an idea what I did wrong? I probably made a mistake when I tried to create the fixture, but I don't know what to improve exactly. But the lightbulbs stay off too when I move the channels in Simple Desk.

Any other suggestions? So, left one down, all others up I couldn't get a laser working this way. General Questions and Information. No Number of Channels: Can withstand adverse conditions. This website uses cookies to improve your experience while you navigate through the website. Out of these cookies, the cookies that are categorized as necessary are stored on your browser as they are as essential for the working of basic functionalities of the website.

We also use third-party cookies that help us analyze and understand how you use this website. These cookies will be stored in your browser only with your consent. You also have the option to opt-out of these cookies. But opting out of some of these cookies may have an effect on your browsing experience. Necessary cookies are absolutely essential for the website to function properly.

This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.

Skip to content. This website uses cookies to improve your experience. We'll assume you're ok with this, but you can opt-out if you wish. Privacy Overview This website uses cookies to improve your experience while you navigate through the website.

Privacy Overview.